Contiki-NG
|
Defines related to the SmartRF06EB. More...
Modules | |
SmartRF06EB Buttons | |
Generic module controlling buttons on the SmartRF06EB. | |
SmartRF06EB Sensors | |
Generic module controlling sensors on the SmartRF06EB. | |
Files | |
file | board.h |
Header file with definitions related to the I/O connections on the TI SmartRF06EB. | |
SmartRF LED configuration | |
LEDs on the SmartRF06 (EB and BB) are connected as follows:
LED1 shares the same pin with the USB pullup | |
#define | LEDS_CONF_YELLOW 1 |
#define | LEDS_CONF_GREEN 2 |
#define | LEDS_CONF_ORANGE 4 |
#define | LEDS_ARCH_L1_PORT GPIO_C_NUM |
#define | LEDS_ARCH_L1_PIN 1 |
#define | LEDS_ARCH_L2_PORT GPIO_C_NUM |
#define | LEDS_ARCH_L2_PIN 2 |
#define | LEDS_ARCH_L3_PORT GPIO_C_NUM |
#define | LEDS_ARCH_L3_PIN 3 |
#define | LEDS_ARCH_L4_PORT GPIO_C_NUM |
#define | LEDS_ARCH_L4_PIN 0 |
#define | LEDS_CONF_RED 8 |
#define | LEDS_CONF_COUNT 4 |
USB configuration | |
#define | USB_PULLUP_PORT GPIO_C_NUM |
#define | USB_PULLUP_PIN 0 |
UART configuration | |
On the SmartRF06EB, the UART (XDS back channel) is connected to the following ports/pins
We configure the port to use UART0. To use UART1, replace UART0_* with UART1_* below. | |
#define | UART0_RX_PORT GPIO_A_NUM |
#define | UART0_RX_PIN 0 |
#define | UART0_TX_PORT GPIO_A_NUM |
#define | UART0_TX_PIN 1 |
#define | UART1_CTS_PORT GPIO_B_NUM |
#define | UART1_CTS_PIN 0 |
#define | UART1_RTS_PORT GPIO_D_NUM |
#define | UART1_RTS_PIN 3 |
SmartRF Button configuration | |
Buttons on the SmartRF06 are connected as follows:
| |
#define | BUTTON_SELECT_PORT GPIO_A_NUM |
BUTTON_SELECT -> PA3. | |
#define | BUTTON_SELECT_PIN 3 |
#define | BUTTON_SELECT_VECTOR GPIO_A_IRQn |
#define | BUTTON_LEFT_PORT GPIO_C_NUM |
BUTTON_LEFT -> PC4. | |
#define | BUTTON_LEFT_PIN 4 |
#define | BUTTON_LEFT_VECTOR GPIO_C_IRQn |
#define | BUTTON_RIGHT_PORT GPIO_C_NUM |
BUTTON_RIGHT -> PC5. | |
#define | BUTTON_RIGHT_PIN 5 |
#define | BUTTON_RIGHT_VECTOR GPIO_C_IRQn |
#define | BUTTON_UP_PORT GPIO_C_NUM |
BUTTON_UP -> PC6. | |
#define | BUTTON_UP_PIN 6 |
#define | BUTTON_UP_VECTOR GPIO_C_IRQn |
#define | BUTTON_DOWN_PORT GPIO_C_NUM |
BUTTON_DOWN -> PC7. | |
#define | BUTTON_DOWN_PIN 7 |
#define | BUTTON_DOWN_VECTOR GPIO_C_IRQn |
#define | PLATFORM_HAS_BUTTON 1 |
#define | PLATFORM_SUPPORTS_BUTTON_HAL 1 |
ADC configuration | |
These values configure which CC2538 pins and ADC channels to use for the ADC inputs. ADC inputs can only be on port A. | |
#define | ADC_ALS_PWR_PORT GPIO_A_NUM |
ALS power GPIO control port. | |
#define | ADC_ALS_PWR_PIN 7 |
ALS power GPIO control pin. | |
#define | ADC_ALS_OUT_PIN 6 |
ALS output ADC input pin on port A. | |
Device string used on startup | |
#define | BOARD_STRING "TI SmartRF06 + cc2538EM" |
Defines related to the SmartRF06EB.
This file provides connectivity information on LEDs, Buttons, UART and other SmartRF peripherals
Notably, PC0 is used to drive LED1 as well as the USB D+ pullup. Therefore when USB is enabled, LED1 can not be driven by firmware.
This file can be used as the basis to configure other platforms using the cc2538 SoC.