Header file with definitions related to the I/O connections on the Zolertia's Firefly platform, Zoul-based. More...

#include "dev/gpio.h"
#include "dev/nvic.h"

Macros
Firefly LED configuration
LEDs on the Firefly are connected as follows: LED1 (Red) -> PD5 LED2 (Green) -> PD4 LED3 (Blue) -> PD3 LED1 pin exposed in JP2 connector LED2 pin exposed in JP2 connector LED3 pin exposed in JP2 connector
UART configuration
On the Firefly, the UARTs are connected to the following ports/pins: UART0: RX: PA0, connected to CP2104 serial-to-usb converter TX pin TX: PA1, connected to CP2104 serial-to-usb converter RX pin UART1: RX: PC1 TX: PC0 CTS: not used, one suggestion however is to use PD1 RTS: not used, one suggestion however is to use PD0 We configure the port to use UART0 and UART1, CTS/RTS only for UART1, both without a HW pull-up resistor. UART0 is not exposed anywhere, UART1 pins are exposed over the JP3 connector.
#define	UART1_CTS_PORT (-1)
	GPIO_D_NUM.

#define	UART1_CTS_PIN (-1)
	1

#define	UART1_RTS_PORT (-1)
	GPIO_D_NUM.

#define	UART1_RTS_PIN (-1)
	0

ADC configuration
These values configure which CC2538 pins and ADC channels to use for the ADC inputs. There pins are suggested as they can be changed, but note that only pins from PA can be configured as ADC. ADC1: up to 3.3V. ADC2: up to 3.3V. ADC3: up to 3.3V. ADC4: up to 3.3V. ADC5: up to 3.3V. ADC6: up to 3.3V, shared with user button. Only ADC1 and ADC3 are enabled as default. The internal ADC reference is 1190mV, use either a voltage divider as input, or a different voltage reference, like AVDD5 or other externally (AIN7 or AIN6).
#define	ADC_SENSORS_PORT GPIO_A_NUM
	ADC GPIO control port.

#define	ADC_SENSORS_ADC1_PIN 5
	ADC1 to PA5

#define	ADC_SENSORS_ADC2_PIN 4
	ADC2 to PA4

#define	ADC_SENSORS_ADC3_PIN 2
	ADC3 to PA2

#define	ADC_SENSORS_ADC4_PIN 6
	ADC4 to PA6

#define	ADC_SENSORS_ADC5_PIN 7
	ADC5 to PA7

#define	ADC_SENSORS_ADC6_PIN (-1)
	ADC6 not declared

#define	ADC_SENSORS_MAX 5
	Maximum sensors

Firefly Button configuration
Buttons on the Firefly are connected as follows: BUTTON_USER -> PA3, S1 user button, shared with bootloader BUTTON_RESET -> RESET_N line
#define	BUTTON_USER_PORT GPIO_A_NUM
	BUTTON_USER -> PA3.

SPI (SSI0) configuration
These values configure which CC2538 pins to use for the SPI (SSI0) lines, reserved exclusively for the CC1200 RF transceiver. These pins are exposed to the JP3 connector. To disable the CC1200 and use these pins, just remove the R10 resistor (0 ohm), which powers both the CC2538 and CC1200 to only power the SoC. TX -> MOSI, RX -> MISO
SPI (SSI1) configuration
These values configure which CC2538 pins to use for the SPI (SSI1) lines, exposed over JP3 connector. TX -> MOSI, RX -> MISO
I2C configuration
These values configure which CC2538 pins to use for the I2C lines, exposed over JP3 connector.
Dual RF interface support
Enables support for dual band operation (both CC1200 and 2.4GHz enabled). Unlike the RE-Mote, the Firefly doesn't have a RF switch, so both interfaces should be always enabled if the R10 resistor is mounted. If only using the 2.4GHz RF interface, the resistor can be removed to power-off the CC1200.
CC1200 configuration
These values configure the required pins to drive the CC1200 None of the following pins are exposed to any connector, kept for internal use only
Device string used on startup

Detailed Description

Header file with definitions related to the I/O connections on the Zolertia's Firefly platform, Zoul-based.

Note: Do not include this file directly. It gets included by contiki-conf after all relevant directives have been set.

Definition in file board.h.

Macros

Detailed Description